Gambro Wro 95 Service Manual
Put the chemical tube in your fluid to pull up, connect to back of machine. Turn on and press chemical disinfect.
It takes it quite a while to pull I'd say at least 15-20 minutes. When it is done both rinse and chemical disinfect will flash. If you pull the chemical tube and press the rinse button for less than 5 seconds it will do a dwell period and then automatically go into a rinse after the dwell. It takes a good couple of hours to run the whole thing.
If you want to let the chemical dwell for a long period of time you can just turn it off and you will have only rinse as a option when turned on next. Location: Ann Arbor, MI Registered: 16 September 2009 Ignored post by posted 09 June 2010 06:27 PM posted 10 June 2010 06:15 AM. I do a similar procedure as Joe for disinfection, but for cleaning, as least in the manual, is tells you to switch some tubing around and push a different combination of buttons.(Place inlet & drain water lines in 5L of cleaning solution; press 'Rinse' and after it starts to flash from low pressure, press & hold 'Mute' button & then press 'Chem Dis' button) This will allow the RO to run in a low pressure situation and creates a recirc of the cleaning solution between the inlet and drain. In the operator manual I have, its under 'Maintenace 4:13'. Posted 10 June 2010 07:53 PM.
. Page 2 and 3:. Page 4 and 5:.
Page 6 and 7:. Page 8 and 9:. Page 10 and 11:.
Page 12 and 13:. Page 14 and 15:.
Page 16 and 17:. Page 18 and 19:.
Page 20 and 21:. Page 22 and 23:. Page 24 and 25:. Page 26 and 27:.
Page 28 and 29:. Page 30 and 31:. Page 32 and 33:. Page 34 and 35:.
Gambro Wro 95 Service Manual
Page 36 and 37:. Page 38 and 39:. Page 40 and 41:. Page 42 and 43:. Page 44 and 45:.
Page 46 and 47:. Page 48 and 49:.
Page 50 and 51:. Page 52 and 53: F. 4 POLES (MOD II) 10 PK 694. Page 54 and 55: F. 6 POLES (MOD II) 10 PK 694. Page 56 and 57: SPARE PART INFORMATION 6946925 14mm. Page 58 and 59: FUSE T 3.15 AMP 5X20 250V,10 PK 694.
Page 60 and 61: 6961288 O-RING 7mm OD INSTRUCTION D. Page 62 and 63: INSTALLATION INSTRUCTIONS 903171620. Page 64 and 65: INSTRUCTION DOCUMENT INC.
Page 66 and 67: INSTRUCTION DOCUMENT INC. Page 68 and 69: CONNECTOR “ L “ SILICONE 5PK 69. Page 70 and 71: BLD PHOTODIODE ASSY. 6955983 DC MOT. Page 72 and 73: MAIN SWITCH 15 AMP 6956833 SPARE PA. Page 74 and 75: INSTRUCTION DOCUMENT INC.
Page 76 and 77: TRANSFORMER IN PWR SUP. 6957351 NI-. Page 78 and 79: MALE SCREW KITS FOR THE “D” CON.
Page 80 and 81: INSTRUCTION DOCUMENT INC. Microsoft access 2016 training manual. Page 82 and 83: INSTRUCTION DOCUMENT INC. Page 84 and 85: IN-OUT CONNECTORS KIT (3 PIECES) 69. Page 86 and 87: PNEUMATIC SPRING 6960116 O-RING 2-0. Page 88 and 89: P2 PUMP CALIBRATION TOOL 6960942 HE. Page 90 and 91: DIALYSATE SAMPLING CONN.
6961031 HE. Page 92 and 93: 6955942 T CONNECTOR (SILICONE) FLOW.
Page 94 and 95: P. MOTHER BOARD 6961148 P.S. +24. Page 96 and 97: O-RING MOUNTING TOOL 6961189 RESTRI. Page 98 and 99: SILICONE SPRAY 6961353 L CONN. Page 100 and 101: INSTALLATION INSTRUCTIONS 903107530.
Page 102 and 103: INSTRUCTION DOCUMENT INC. Page 104 and 105: INSTRUCTION DOCUMENT INC. Page 106 and 107: OBSOLETE PART Use part number 69825. Page 108 and 109: I/O SELECTION PART B GAL 6964191 I/.
Page 110 and 111: INSTRUCTION DOCUMENT INC. Page 112 and 113: INSTRUCTION DOCUMENT INC. Page 114 and 115: INSTRUCTION DOCUMENT INC.
Page 116 and 117: 6966584 UNIVERSAL PUMP INSERT 69516. Page 118 and 119: 8mm 6.5mm “T” CONN.